Linear DXS-54 Bedienungsanleitung PDF herunterladen

DXS-54 Installation Instructions

Linear P/N: 209509 B

Material: 20 Lb. Mead Bond

Size: 8 1/2" x 11"

Ink: PMS 561 (Aqua)

Scale: 1-1

DXS-54

SUPERVISED

WIRELESS

MOTION

DETECTOR

Installation Instructions

(760) 438-7000

•

FAX (760) 438-7043

USA & Canada (800) 421-1587 & (800) 392-0123

Toll Free FAX (800) 468-1340

PRODUCT DESCRIPTION

The DXS-54 is a battery powered passive infrared motion detector with

a built-in transmitter designed for use with Linear’s DXS and DX format

receivers. This transmitter can be used in a variety of motion detection

applications. When the passive infrared sensor detects motion in its

field of view, the transmitter sends a digitally coded wireless signal to

its companion receiver.

The digital DXS code format features over a million possible codes.

The DXS transmitters are precoded at the factory to unique codes, so

no field coding is required. The DXS-54 can send three different

signals: alarm, low battery and status.

For versatility,

any transmitter can be programmed into any receiver

channel.

Receivers must be programmed to the transmitter’s code

before system testing and operation. Refer to the receiver’s

instructions for details on programming.

In a typical installation, the motion detector is mounted indoors in a

corner or on a wall between six and eight feet high. The sensor will

monitor the infrared level in its detection pattern. If the level increases

or decreases rapidly (as when a person or animal moves through the

area) the transmitter triggers, sending an alarm signal to the receiver.

The unit is powered from a 9-Volt alkaline battery. The battery’s life

can be up to three years depending on the area’s traffic. When the

battery gets low, the test indicator will flash and a low battery signal

will be sent to the receiver when the detector senses motion.

Approximately every hour, the DXS-54 will send a status transmission

to the receiver. The hourly signal updates the receiver to the

transmitter’s condition. By monitoring status transmissions, the

receiver can determine if a transmitter has a low battery or has been

removed from the system. DXS format receivers can monitor status

signals, DX format receivers cannot.

To conserve battery life, during normal operation,

the detector can

trigger the transmitter a maximum of once every four minutes.

For setup and testing, pressing the detector’s test button places the

unit in walk test mode for four minutes. The installer can walk in front

of the unit while viewing the red test indicator through the detector’s

lens to determine the detection area.

In walk test, an alarm signal is sent each time the walk test indicator

lights. During normal operation, the detector requires a “pulse count”

of three events in eight seconds before sending an alarm transmission.

DXS-54 FEATURES DETECTION PATTERN TYPICAL INSTALLATION

CONNECTING BATTERY MOUNTING DETECTOR BASE WALK TEST

PROGRAM RECEIVER AND TEST CHANGING BATTERY LINEAR LIMITED WARRANTY

This Linear product is warranted against defects in material and workmanship for twelve (12) months. The

Warranty Expiration Date is labeled on the product.

This warranty extends only to wholesale customers

who buy direct from Linear or through Linear’s normal distribution channels.

Linear does not warrant

this product to consumers.

Consumers should inquire from their selling dealer as to the nature of the

dealer’s warranty, if any.

There are no obligations or liabilities on the part of Linear corporation for

consequential damages arising out of or in connection with use or performance of this product or

other indirect damages with respect to loss of property, revenue, or profit, or cost of removal,

installation, or reinstallation.

All implied warranties, including implied warranties for merchantability and

implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product.

This

Linear Corporation Warranty is in lieu of all other warranties express or implied.

For warranty service on Linear equipment return product, at sender’s expense to:

All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact

Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.

IMPORTANT !!!

Linear radio controls provide a reliable communications link and fill an important need in portable wireless

signalling. However, there are some limitations which must be observed.

✶

For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as

Part 15 devices. As such, they have limited transmitter power and therefore limited range.

✶

A receiver cannot respond to more than one transmitted signal at a time and may be blocked by

radio signals that occur on or near their operating frequencies, regardless of code settings.

✶

Changes or modifications to the device may void FCC compliance.

✶

Infrequently used radio links should be tested regularly to protect against undetected interference

or fault.

✶

A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale

distributor or dealer, and these facts should be communicated to the ultimate users.

DXS

FORMAT

WALK

TEST

BUTTON

MOTION

DETECTOR

LENS

CASE

LOCKING

SCREW

(ON BOTTOM)

TEST INDICATOR

BEHIND LENS

(BLINKS DURING

WALK TEST, FLASHES

WHEN BATTERY IS LOW

DURING MOTION)

OPERATING

TEMPERATURE

RANGE:

+32° TO +120° F

(0° TO +49° C)

DETECTION

AREA

30 FEET

6-8 FEET

SIDE

VIEW

TOP

VIEW

MOTION

DETECTOR

IN CORNER

DON'T POINT AT HEAT SOURCES

(HEATERS, ETC.), WINDOWS, OTHER

MOTION DETECTORS OR DOOR/WINDOW

TRANSMITTERS

BEDROOM

BATH

KITCHEN

FRONT

ROOM

(FOR INDOOR

USE ONLY)

MOUNT

DETECTOR

SO THAT

INTRUDER

WILL CROSS

BEAMS

MOTION

DETECTOR

REMOVE

SCREW

AND OPEN

CASE

CONNECT 9-VOLT ALKALINE

BATTERY TO BATTERY CLIP

(PLUS SIDE UP)

NOTE: BE SURE TO

REPLACE THE CASE

SCREW AFTER CLOSING

THE CASE

PUNCH OUT REQUIRED HOLES

FOR SCREW MOUNTING

USE CENTER

HOLES FOR

WALL

MOUNTING

USE SIDE HOLES

FOR CORNER

MOUNTING

NOTE:

THE DETECTOR CAN

BE MOUNTED WITH

DOUBLE STICK TAPE,

BUT IS NOT ALLOWED

IN UL INSTALLATIONS

MOUNT

DETECTOR

6-8 FEET

HIGH

MOUNTING THE DETECTOR

IN A CORNER IS PREFERRED

AFTER MOUNTING, SNAP

DETECTOR ONTO BASE

AND REPLACE CASE SCREW

PUSH

WALK

TEST

BUTTON

WALK IN FRONT OF UNIT

WHILE WATCHING RED LIGHT

UNIT WILL STAY IN

WALK TEST MODE

FOR 4 MINUTES AFTER

PRESSING WALK TEST

BUTTON

VERIFY THAT DETECTION

PATTERN COVERS DESIRED

AREA

NOTE: AFTER INITIAL SETUP

WALK TEST UNIT ANNUALLY

AFTER PROGRAMMING RECEIVER

TO THE TRANSMITTER'S CODE

TEST THE SYSTEM

STAYING CLEAR, WAIT AT LEAST

FIVE MINUTES BEFORE WALKING

INTO THE DETECTION AREA

WALK ACROSS THE DETECTION

PATTERN AND VERIFY THAT

THE RECEIVER ACTIVATES

FOR PROGRAMMING,

REFER TO THE RECEIVER'S

INSTRUCTIONS

REMOVE

SCREW

AND OPEN

CASE

WHEN THE DETECTOR

HAS A LOW BATTERY:

REPLACE THE BATTERY WITH

A FRESH 9-VOLT ALKALINE

OR LITHIUM BATTERY

(PLUS SIDE UP)

USE ALKALINE

OR LITHIUM

BATTERIES ONLY

SNAP DETECTOR ONTO BASE

AND REPLACE CASE SCREW

WHEN FINISHED

Inhaltsverzeichnis

Seite 1 - DETECTOR

DXS-54 Installation InstructionsLinear P/N: 209509 BMaterial: 20 Lb. Mead BondSize: 8 1/2" x 11"Ink: PMS 561 (Aqua)Scale: 1-1DXS-54SUPERVISE

Kommentare zu diesen Handbüchern

Keine Kommentare

Linear DXS-54 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sicherheit Linear DXS-54 herunter. Linear DXS-54 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheit Linear DXS-54