Linear wt00z-1 Bedienungsanleitung PDF herunterladen

NOTE: This module must be “included in the Network” only where it will be permanently installed. The proper operation of this node in the

mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” conﬁ gure this module.

WTOOZ-1 WALL MOUNTED TRANSMITTER

Linear’s family of Z-Wave certiﬁ ed wireless lighting controls (switches,

dimmers, outlets and plug-in modules) brings a new level of intelligent

wireless capability to commercial and residential environments.

The Z-Wave wireless protocol is an international wireless standard

for remote home automation, security and other applications.

Embedded in each device, the Z-Wave smart chip enables two-way RF

communication among hundreds of Z-Wave enabled devices, allowing

products and services from multiple manufacturers to work seamlessly.

Linear Z-Wave products are easy to install, and allow dealers to create

an integrated wireless network with nearly limitless expansion and

interoperability with security and health monitoring systems, energy

management, home entertainment, appliances, and more.

INSTALLATION

DANGER! SHOCK HAZARD. Read and understand these

instructions before installing. This device is intended for installation in

accordance with the National Electric code and local regulations in the

United States, or the Canadian Electrical Code and local regulations

in Canada. It is recommended that a qualiﬁ ed electrician perform this

installation. Retain instructions for future use. With power off, wire this

WT00Z-1 according to the diagram shown above. If more than one

WT00Z-1 is to be installed in a wall box, scored tabs on the side can

be broken off by bending back and forth with pliers, to accommodate

proper ﬁ t. Apply power when completed. Refer to your Controller

operating instructions on how to include this module in the RF network

INCLUDING WT00Z-1 TO THE NETWORK

STEP 1. Prepare the Controller to include a unit to the network by

adding it to a group (method of adding a node to the network). Refer

to controller instructions.

STEP 2. The WT00Z-1 must be in its permanently installed

location. Tap either the top or bottom of the WT00Z-1 once.

STEP 3. You should see an indication on your Controller that the

“device was included” in the network.

NOTE: If you have trouble adding the WT00Z-1 to a group it may be

that the Home ID and Node ID were not cleared from it after testing.

You must ﬁ rst “RESET UNIT” with your controller to remove it from

the network. Although adding it to a group includes it in the network,

removing it from a group does not remove it from the network. If

removed from a group, it functions as a repeater (only). “RESET UNIT”

removes it completely from the network.

WT00Z-1

Radio Frequency (RF) Controlled, 120 VAC, Wall Mounted

Transmitter, Series 300

SUPPLIED WITH DECORATIVE SWITCH PLATE

NEUTRAL

120 VAC

PUSH ON (PUSH

& HOLD TO BRIGHTEN)

WHITE

LINE

BLACK

PUSH OFF

(PUSH AND

HOLD TO DIM)

STATUS LED

GREEN

GROUND

PUSH TOP OR

BOTTOM OF PADDLE

SWITCH ONCE TO

INCLUDE IN NETWORK

TO MOUNT MORE THAN ONE

WT00Z-1IN A BOX, SCORED TAB

WILL BREAK FLUSH WITH EDGE

OF PLASTIC

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Transmitter, Series 300

1NOTE: This module must be “included in the Network” only where it will be permanently installed. The proper operation of this node in the mesh networ

Seite 2 - CONFIGURATION

2OPERATIONBefore you can control Z-Wave devices you must associate the devices you want to control from the WT00Z-1.Turning Z-Wave devices On or Off1.

Seite 3 - SPECIFICATIONS

3Adjusting Dim RateFor example: There are 3 sets of parameters that can adjust the dimming rate of the WT00Z-1.1. One set to control how fast the dim

Seite 4 - WARRANTY

Kommentare zu diesen Handbüchern

Keine Kommentare

Linear wt00z-1 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Nein Linear wt00z-1 herunter. Linear wt00z-1 User's Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern